Square foot gardening pdf download






















Starting with big-picture questions—what is a foot, and what is it used for? How does it work, both on its own and as part of a whole? Remove weeds, rocks and trash, and work the top 8 to 10 inches of soil before planting. Work the soil only when it is dry enough not to stick to garden tools. Use 2 to 3 pounds of fertilizer, such as , for every square feet of garden area. Spread the fertilizer evenly over the soil and work it into the soil 3 to 4 inches deep. Rake the soil to smooth the surface.

Sweet corn is a warm-season crop and must be planted after the soil warms and there is no more danger of frost. If you have room, plant again when the first corn plants have three to five leaves. This usually takes 2 to 3 weeks. You will need 1 to 2 ounces of seed for every feet of row. Sweet corn grows best when planted in several short rows instead of one long row. This makes it easier for the corn plants to pollinate, and good pollination is necessary for ears of corn to have plump, juicy kernels.

Figure 1. Plant corn in several short rows, not in one or two long rows. Plant the corn seeds about 1 inch deep and 3 to 4 inches apart in the row. After the plants are up, thin them to 1 foot apart. Take the needed measurements and write down the data on the spaces provided. Information Necessary in a Body Chart Height — Data can be gathered with the use of a measuring tape. The height can be measured either in feet and inches, or in centimeters. Body Weight — Data can be gathered with the use of a weighing scale.

Height of Building max. Encroachment Plane Origin Height. Angle of Encroachment Plane. These zones are intended to address issues of neighborhood character and to facilitate the compatibility of new construction, additions and alterations in single-family neighborhoods where the predominate building form includes a two-story mass at the front of the lot and a one-story mass at the rear of the lot.

The intent of this variation is to allow taller massing at the front of the lot and mandate shorter massing at the rear of the lot that respects the scale and form of other houses in the vicinity. The maximum Residential Floor Area contained in all buildings shall not exceed the specified Residential Floor Area ratio for the corresponding zone per size of the lot as listed in Table The maximum lot coverage, the maximum height of the front and rear masses, and the maximum height at which the encroachment plane begins for the front and rear masses shall not exceed the amounts specified for each zone in Table Front Mass.

Front envelope depth, from front yard setback min. Height of Mass max. Rear Mass. Rear envelope depth, from rear yard setback min. These zones are intended to address issues of neighborhood character and to facilitate the compatibility of new construction, additions and alterations in single-family neighborhoods where the predominate building form includes a one-story mass at the front of the lot and a two-story mass at the rear of the lot.

The intent of this variation is to mandate shorter massing at the front of the lot and allow taller massing at the rear of the lot that respects the scale and form of other houses in the vicinity.

Said lots shall be exempt from the Front Mass development standards listed in Table These zones are intended to address issues of neighborhood character and to facilitate the compatibility of new construction, additions and alterations to one-family houses in Hillside Areas having an existing variety of building forms.

Verification of Existing Residential Floor Area. For additions with cumulative Residential Floor Area of less than 1, square feet constructed after January 1, , or remodels of buildings built prior to January 1, , the existing Residential Floor Area shall be determined based on the building records or the building square footage shown on the most recent Los Angeles County Tax Assessor's records at the time the plans are submitted to the Department of Building and Safety and a plan check fee is paid.

Except that Residential Floor Area may be calculated as defined in Section Any work that does not qualify as a remodel, as defined in the paragraph below, or additions that are 1, square feet or larger shall require a complete set of fully dimensioned plans with area calculations of all the structures on the lot prepared by a licensed architect or engineer.

For the purposes of implementing this subdivision, a remodel shall mean the alteration of an existing building or structure provided that at least 50 percent of the perimeter length of the contiguous exterior walls and 50 percent of the roof are retained. Definitions and Standards. For the purposes of this Subsection the following definitions and standards shall apply:.



0コメント

  • 1000 / 1000